Sunday, August 25, 2013

Recyclable Racers

I can't tell you how many times a toilet paper tube has saved my sanity as a mom. Punching four holes with a simple hole punch and using a stirrer straw or a kabob skewer for axles takes 3 minutes max and can lead to hours of play. You can attach a balloon to a straw with a rubber band and then attach the straw to the recyclable via double sided masking tape. After blowing up the balloon, watch it race across your house, driveway, backyard, park, wherever! If your kid is too small for balloons, set up a cardboard box as a ramp and bring on the giggles. You can also add a sail to the car and watch the car move as your child blows on it. Sharing this knowledge was the goal of this month's Science Saturday.

We had a great turn out for our Science Saturday this month! We had it in a park with great sidewalks and access to sand (for weight), but unfortunately, we only one table to assemble things. It was crowded, but we sure had some fun. The goal was to learn about equal and opposite reactions, friction, and general engineering (tweaking your designs for better performance).

How to make your own recyclable racer:


1. Pick out a recyclable you think will make a great race car. I'm always fond of soda bottles. Water bottles nowadays are made with less plastic and are too squishy. I also wouldn't recommend aluminum cans since they are squishy and super light.

Tape standard straws to the bottom of the recyclable
Weigh down the car with washers or sand if necessary

2. Attach two pieces of a normal size drinking straw (small pieces are fine, think cut into 4ths or more) to the underside of your recyclable. This will hold your axles for the wheels, allowing them to move without friction. Note, in previous versions of balloon racers, I used an awl and pre-punched holes into the bottles. Using straws gives you a lot more freedom with adjustments (I hardly ever punch straight holes) and is safer all around (luckily, no battle wounds from before). You want the straw pieces to be parallel to each other and as straight as possible (perpendicular to the direction you'd like the car to move).

3. Stick your axles through the straws. We used stirrer straws for the little recyclables and kabob sticks for the bigger ones. I'd recommend chopping off the points of the skewers before giving to a small child.


4. For wheels, we pre-drilled holes into bottle caps, I made some circular corrugated cardboard wheels using a compass-like tool for cutting circles (affiliate link), and I bought some foam discs. Nobody chose the cardboard wheels. It was split pretty 50/50 on foam and bottle cap wheels.

5. Attach your wheels to the axles. I recommend that the wheels not touch the recyclable since friction will slow down your race car. At this point, you can glue them into place with a hot/warmish glue gun. Whether you use a press fit or you glue the wheels, the wheels should spin with your axle. Make sure the wheels are straight or your car might veer.

6. Attach a balloon to a straw with a rubber band. I found the bubble tea straws (affiliate link) work really well (we cut them into 3rds to reduce costs - though I linked to Amazon, I found these at our local BB&Beyond for $2). You can use a standard straw, but you have to walk the fine line between the rubber band being too tight and crushing the straw or not being tight enough and you can't blow up the balloon.

7. Tape the balloon to the car. I recommend a place where it can hang off the back and you don't have to keep taking it off and on to blow it up.

8. Blow up your balloon and pinch tight, or put your finger over the straw to block the air. Set your car down and let go of the balloon.

9. If your car flips, consider weighing it down (washers or sand do a great job). You can also switch what direction of your car is front (ie. flip the balloon around so it points from the opposite end of the racer).

10. Make adjustments and see if your car can go even faster!

I was able to pull out my camera for video of a few racers we had in the middle of the activity. Parents had to help the little ones blow up the balloons, but fun was had by all:


I think these racers went further than last years balloon racers!

Related Posts:

Sunday, August 18, 2013

Next Science Saturday and Apologies

The next Science Saturday is this Saturday, August 24, 2013.

We'll be making race cars out of recyclables and learning about gravity and equal and opposite reactions. You can make balloon racers, sail cars, or figure out how to make your car run using forms of energy (elastic, potential, etc). It'll be tons of fun! Bring your own recyclable or use some of the ones we'll bring.

Email me using the link on the left <<, and I can give you detailed information of Science Saturday.

In other news, I apologize for taking a little bit of a blogging break. We still have been doing science at our house. I have two lessons half way composed. Hopefully, one of them will make it to the blog by the end of the week.

Saturday, August 10, 2013

Pocket Frog

J's school has been doing some cool themed weeks this summer. They've had two weeks learning about the ocean, and the last two weeks were spent learning about the rain forest. On Wednesdays, they have an opportunity to bring something to share with the class that is related to the theme (think "show and tell").

Lucky for J, I was one of those Beanie Baby collectors (not hard core, and J has since ripped off most of the tags). I think we've found a different Beanie Baby to share each week for the past month (thank you McD's). Anyways, this past Wednesday as I was dropping him off at school, J insisted on keeping his "red eyed tree frog" in his pocket instead of his cubbie. Immediately, I thought of this engineer and the frog joke, and left school with a gigantic smile on my face. I made a mental note to share with you in case you haven't heard it.

I love my mini-nerd.

Tuesday, August 6, 2013

Which cookie would you choose?

We made cookies for dessert, and J got to select the one he wanted. He took his cookie before I got the picture, but he definitely knows if you only get one cookie, you better select the biggest one for the most pleasureful experience. There was one larger, standout cookie that was the cookie that got the excess batter at the end of the batch.

While helping me dish out how many cookies fit on a pan, we counted 4 rows of 3, which made 12 cookies!


Or is it 3 rows of 4? It's still 12 cookies!!

I love incorporating math into our everyday lives.